Victron BCD 802 2 batteries 80A (combiner diode)
Diode Battery Combiners are used to guarantee continuous DC power to mission critical equipment, such as an electronic engine control system. With a Diode Battery Combiner two or more DC power sources can be used in parallel to supply the mission critical load. Failure of one source will not interrupt power to the critical load.
Victron Argofet 200-3 Three batteries 200A
Similarly to Argodiode battery isolators, Argofet isolators allow simultaneous charging of two or more batteries from one alternator (or a single output battery charger), without connecting the batteries together. In contrast with Argodiode battery isolators, Argofet isolators have virtually no voltage loss. Voltage drop is less than 0,02 Volt at low current and averages 0,1 Volt at higher currents.
Victron Orion-Tr 12/12-18A (220W) Isolated DC-DC converter
Remote on/off
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on/off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
All models are short circuit proof and can be paralleled to increase output current. An unlimited number of units can be connected in parallel.
IP43 protection
When installed with the screw terminals oriented downwards.
Screw terminals
No special tools needed for installation.
Input fuse
On 12V and 24V input models only.
Victron Orion IP67 24/12-10A (120W) DC-DC Converter Non Isolated
Completely encapsulated: waterproof, shockproof and ignition protected
Water, oil or dirt will not damage the Orion IP67 DC-DC Converter. The casing is made of cast aluminium and the electronics are moulded in resin.
Power Protectors by Exide India
Type PP200-12 Deep Cycle AGM VRLA Sealed Lead Acid Battery
8 Year Design Life
450 - 650 Discharges to 80% Depth of Charge Cycle Life
12 Volts
200 Amp Hour
Please contact us for quantity discounts
Email: info@createenergy.co.za or telephone: +(27) 11 888 0410
Victron Skylla-TG 24/50(1+1) 230V
A powerful, waterproof and intelligent battery charger with a 7-stage adaptive charge algorithm, suitable for a wide range of battery types and chemistries featuring a dedicated Lithium-ion charge algorithm.
The wide range universal input voltage adds flexibility to the installation, the charger will maintain its full output power no matter where it is located in the world.
The IP65 rating makes this charger especially suitable for marine, mobile, and industrial applications and it can withstand the rigors of an adverse environment: heat, humidity and salt air.
- 230VAC
- 24VDC charger
- 50A charger
- 1 full output rated
- 1 output 4A rated
Victron EasySolar-II 48/3000/35-32 MPPT 250/70 GX
All-in-one solar power solution
The Victron EasySolar-II GX integrates the following elements:
• A MultiPlus-II inverter/charger
• A SmartSolar MPPT -Tr solar charge controller
• A GX device with a 2 x 16-character display.
These elements come prewired together inside a single unit. This greatly simplifies most installations, saving time and money.
48VDC, 3000VA
35A Charger, 32A Transfer Switch
250VDC 70A MPPT
Victron Phoenix IP43 Smart Charger 12 V / 30 A (1+1) 120 - 240V ac
</ = 30 A Main House Battery Charger Plus </= 4 A Battery Maintainer for Primary Cranking Battery
Wide AC Input Range 120-240 Vac
Adjustable DC Output Current Setting
Ready for Parallel and Redundant Operation
Natural Convection Cooling
Adaptive 5 Stage Charge Algorithm
Less than 1 mA Self Consumption
Full Rated Output up to 40 Deg C
IP43 Degree of Ingress Protection
Requires CE 13 "Kettle" Plug - Not Included
Victron EV Charging Station NS
The EV Charging Station NS has three-phase and single-phase capabilities. It delivers a maximum of 22kW AC in three-phase or 7.3kW in single-phase mode.
The device is technically identical to the EV Charging Station, but with a new, modern design available in 3 colours and without the built-in LCD screen. Initial setup, configuration and monitoring is done from VictronConnect via Bluetooth and/or the integrated web interface via a WiFi Access Point or a WiFi LAN.
The charger can be fully integrated with and remotely controlled via a Victron Energy GX Device and VRM.
Not only does this EV Charging Station NS fully integrate with a Victron Energy GX device and VRM, if you have solar (within the Victron ecosystem), it can also be set up to allow excess energy from the sun to directly charge your vehicle. Manual and scheduled modes offer even more flexibility to respond to the needs of the EV depending on the system.
It has a fully programmable RGB light ring around the charging port that displays different light effects depending on the current status (disconnected, charging, charged, etc.) to quickly determine the device status.