Victron BlueSolar PWM-LCD&USB 12/24V-20A
Solar charge controller
BlueSolar PWM-LCD&USB
- Liquid Crystal Display
- Two 5 Volt USB outputs
- Lighting control function, fully programmable
- Three stage battery charging (bulk, absorption, float), fully programmable
- Load output with low voltage and manual disconnect (programmable)
- Load output protected against over load and short circuit
- Protected against reverse polarity connection of the solar panels and/or battery
BlueSolar PWM DUO-LCD&USB
All the above-mentioned functions, plus:
- Charges two separate batteries
- Programmable charge current ratio
- External Temperature sensor
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron Orion IP67 24/12-10A (120W) DC-DC Converter Non Isolated
Completely encapsulated: waterproof, shockproof and ignition protected
Water, oil or dirt will not damage the Orion IP67 DC-DC Converter. The casing is made of cast aluminium and the electronics are moulded in resin.
Victron BATTERY SWITCH ON/OFF 275A
- Max.continuouscurrent: 275A
- One minute rating: 450 A
- Cranking rating: 1200 A
- Voltage rating: 48 V
CSB HRL1234WF2 Sealed Lead Acid Battery
8 Year Design Life
12 Volts
9 Amp Hours
Please contact us for quantity discounts
Email: info@createenergy.co.za or telephone: +(27) 11 888 0410
Forbatt 12 Ah 12V LEAD ACID Storage Battery
FORBAT 12V Lead Acid (AGM- VRLA) Battery
12 AH
APPLICATIONS
Server Rooms
UPS
1 Year Limited Warranty
Please contact us for quantity discounts
Email: info@createenergy.co.za or telephone: +(27) 11 888 0410
Victron BatteryProtect 12/24V-65A
The BatteryProtect disconnects the battery from non essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.
The BatteryProtect is a uni-directional device. It can only deal with current in one direction, so either current to a load, or current from a charger, but not both currents at the same time. In addition to this, current only can only flow from the Battery terminal to the Load terminal. In case of use with a load, the battery connects to the Battery terminal, and in case of use with a charger, the charger connects to the Battery terminal.
A cable to connect Digital Multi Control, Phoenix Inverter Control, Interface MK3-USB, VE.Bus connections between multiple VE.Bus devices and to make VE.Bus and VE.Can connections to a GX device.
Victron Current Transformer 100A:50mA for MultiPlus-II (1m) Wire-end
Victron Orion-Tr 24/12-15 (180W) DC-DC converter Non isolated
Completely encapsulated: waterproof, shockproof and ignition protected
Water, oil or dirt will not damage the Orion IP67 DC-DC Converter. The casing is made of cast aluminium and the electronics are moulded in resin.
Victron Wall mounted enclosure for Color Control GX and BMV or MPPT
GIFT VOUCHER www.createenergy.co.za
Value ZAR 500.00
(Five Hundred South African Rand)
Victron BlueSolar PWM-Light Charge Controller 12/24V-30A
Solar charge controller
BlueSolar PWM-Pro
The BlueSolar PWM-Pro series is ready for use with its default settings. It also is fully programmable.
• Lighting control function, fully programmable.
• Three stage battery charging (bulk, absorption, float), fully programmable.
• Integrated battery monitor function (Remote Panel needed to display state of charge).
• Load output with low voltage disconnect and manual control (default setting).
• Optional external temperature sensor.
• Load output protected against over load and short circuit.
• Protected against reverse polarity connection of the solar panels and/or battery.
• Day/night timing options: see manual Remote Panel for details.
BlueSolar PWM-Light
• Load output with low battery voltage disconnect function.
• Lighting control function, one timer only.
• Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting.
• Three stage battery charging (bulk, absorption, float), not programmable.
• Load output protected against over load and short circuit.
• Protected against reverse polarity connection of the solar array and/or battery.
• Day/night timing options: see manual for details
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron BlueSolar PWM-LCD&USB 48V-10A
Solar charge controller
BlueSolar PWM-LCD&USB
- Liquid Crystal Display
- Two 5 Volt USB outputs
- Lighting control function, fully programmable
- Three stage battery charging (bulk, absorption, float), fully programmable
- Load output with low voltage and manual disconnect (programmable)
- Load output protected against over load and short circuit
- Protected against reverse polarity connection of the solar panels and/or battery
BlueSolar PWM DUO-LCD&USB
All the above-mentioned functions, plus:
- Charges two separate batteries
- Programmable charge current ratio
- External Temperature sensor
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron Busbar to connect 5 Modular Mega Fuse Holders (Victron P/N: CIP100200100)
Victron Smart Battery Sense long range (up to 10m)
Smart Battery Sense is a wireless battery voltage and temperature sensor for Victron MPPT Solar Chargers.
With voltage and temperature sense in place, batteries will be better charged; improving charging-efficiency and prolonging battery life.
Victron Argodiode 80-2SC 2 batteries 80A
Argodiode Battery Isolators allow simultaneous charging of two or more batteries from one alternator, without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery. Low voltage drop due to the use of high efficiency Schottky diodes.
Using the VE.Direct to Bluetooth Smart dongle you can display your BMV or MPPT information on iOS and Android devices, using the VictronConnect App. View information wirelessly such as battery status and solar panel power, plus other useful data.
The dongle is able to read data from all products with a VE.Direct port, such as the BMV-70x series battery monitors, Phoenix Inverters with VE.Direct port, MPPT Solar Charge Controllers.
WATERSNAKE 3-BLADE PROP KIT - REINFORCED NYLON
SUITS ALL 44LB, 54 LB, 65LB & 80LB MOTORS
- Made from reinforced nylon
- Strong and durable
- Designed for Watersnake 65lb - 80lb motors*
- Weedless design
- ALSO FITS MOTORGUIDE 44 lb. Thrust & ABOVE MOTORS
Carry Case for Victron Blue Smart IP65 Chargers and Accessories
Suits Victron Bluesmart IP65 Chargers 24 V / 8 A and 12 V / 25 A
Dimensions 345 x 520 x 130mm
Victron BCD 402 2 batteries 40A (combiner diode)
Diode Battery Combiners are used to guarantee continuous DC power to mission critical equipment, such as an electronic engine control system. With a Diode Battery Combiner two or more DC power sources can be used in parallel to supply the mission critical load. Failure of one source will not interrupt power to the critical load.
Victron Current Transformer 100A:50mA for MultiPlus-II (5m) Wire-end
Victron Remote panel for BlueSolar PWM-Pro Charge Controller
Victron BlueSolar PWM-Light Charge Controller 48V-10A
Solar charge controller
BlueSolar PWM-Pro
The BlueSolar PWM-Pro series is ready for use with its default settings. It also is fully programmable.
• Lighting control function, fully programmable.
• Three stage battery charging (bulk, absorption, float), fully programmable.
• Integrated battery monitor function (Remote Panel needed to display state of charge).
• Load output with low voltage disconnect and manual control (default setting).
• Optional external temperature sensor.
• Load output protected against over load and short circuit.
• Protected against reverse polarity connection of the solar panels and/or battery.
• Day/night timing options: see manual Remote Panel for details.
BlueSolar PWM-Light
• Load output with low battery voltage disconnect function.
• Lighting control function, one timer only.
• Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting.
• Three stage battery charging (bulk, absorption, float), not programmable.
• Load output protected against over load and short circuit.
• Protected against reverse polarity connection of the solar array and/or battery.
• Day/night timing options: see manual for details
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron Orion-Tr 24/12-20 (240W) DC-DC converter Non isolated
Completely encapsulated: waterproof, shockproof and ignition protected
Water, oil or dirt will not damage the Orion IP67 DC-DC Converter. The casing is made of cast aluminium and the electronics are moulded in resin.
Replacement Propeller Kit For Watersnake Advance 24 V 95 lb or 12 V 70 lb Brushless Motor
Includes:
Replacement Propeller
Propeller Spanner
Propeller Nut, Washer and Pin
CSB GP12120 Sealed Lead Acid Battery
5 Year Design Life
12V
12Ah
Please contact us for quantity discounts
Email: info@createenergy.co.za or telephone: +(27) 11 888 0410
The ET112 (for single phase max. 100A) and the ET340 (for three phase max. 65A) Energy Meters are typically used in an Energy Storage System.
To measure the power and energy of the whole application at the distribution box. Or to measure the output of a PV Inverter, to display the data on the Color Control GX and the VRM Portal.
Victron Orion IP67 24/12-20A (240W) DC-DC Converter Non Isolated
Completely encapsulated: waterproof, shockproof and ignition protected
Water, oil or dirt will not damage the Orion IP67 DC-DC Converter. The casing is made of cast aluminium and the electronics are moulded in resin.
Victron Busbar to connect 6 Modular Mega Fuse Holders (Victron P/N: CIP100200100)
Victron BlueSolar PWM-LCD&USB 12/24V-30A
Solar charge controller
BlueSolar PWM-LCD&USB
- Liquid Crystal Display
- Two 5 Volt USB outputs
- Lighting control function, fully programmable
- Three stage battery charging (bulk, absorption, float), fully programmable
- Load output with low voltage and manual disconnect (programmable)
- Load output protected against over load and short circuit
- Protected against reverse polarity connection of the solar panels and/or battery
BlueSolar PWM DUO-LCD&USB
All the above-mentioned functions, plus:
- Charges two separate batteries
- Programmable charge current ratio
- External Temperature sensor
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron BlueSolar MPPT 75/10 Retail
Solar charge controller
75VDC / 10A
12/24 Battery
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Fuse Box - 1 in and 6 out with negative bus bar and LED Indicator
- 6 Circuits with Cover and Negative Bus
- Main Line Terminal Rating: M5 Threaded Studs(100a 32V DC Max)
- Wire Size: #4-6 AWG
- Red LED indicates when fuse is broken
- Size of Panel: 87.75mm x 85.0mm
Victron BlueSolar PWM-LCD&USB 48V-20A
Solar charge controller
BlueSolar PWM-LCD&USB
- Liquid Crystal Display
- Two 5 Volt USB outputs
- Lighting control function, fully programmable
- Three stage battery charging (bulk, absorption, float), fully programmable
- Load output with low voltage and manual disconnect (programmable)
- Load output protected against over load and short circuit
- Protected against reverse polarity connection of the solar panels and/or battery
BlueSolar PWM DUO-LCD&USB
All the above-mentioned functions, plus:
- Charges two separate batteries
- Programmable charge current ratio
- External Temperature sensor
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron Shore Adapter Cord 32A/3 to single ph.-CEE Plug 5P/CEE Coupling 3P
- Input voltage, AC (DC) 220
- Input Current: 32 A
- Connects to Either Shore Power Cable or Shore Power Inlet Socket
- Waterproof: IP 56
- CE Certified: yes
Lowrance RSA Inland Waters Chart
On Micro sd Card with SD Card Adapter
Victron BlueSolar PWM-Pro Charge Controller 12/24V-20A
Solar charge controller
BlueSolar PWM-Pro
The BlueSolar PWM-Pro series is ready for use with its default settings. It also is fully programmable.
• Lighting control function, fully programmable.
• Three stage battery charging (bulk, absorption, float), fully programmable.
• Integrated battery monitor function (Remote Panel needed to display state of charge).
• Load output with low voltage disconnect and manual control (default setting).
• Optional external temperature sensor.
• Load output protected against over load and short circuit.
• Protected against reverse polarity connection of the solar panels and/or battery.
• Day/night timing options: see manual Remote Panel for details.
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron Cyrix-ct 12/24V-120A intelligent battery combiner
Victron smallBMS
A simple and low cost alternative to the VE.Bus BMS V2
The smallBMS can replace the VE.Bus BMS V2 in several applications. It is however not suitable for use with VE.Bus MultiPlus and Quattro inverter/chargers: it has no VE.Bus interface. The smallBMS is intended for use with Victron Smart LiFePo4 batteries with M8 circular connectors.
The smallBMS has two outputs, similar to the VE.Bus BMS V2.
CAB-1 Steel Battery Cabinet on Caster Wheels to hold 1 X 100Ah Battery
Victron BCD 802 2 batteries 80A (combiner diode)
Diode Battery Combiners are used to guarantee continuous DC power to mission critical equipment, such as an electronic engine control system. With a Diode Battery Combiner two or more DC power sources can be used in parallel to supply the mission critical load. Failure of one source will not interrupt power to the critical load.
Victron Argodiode 80-2AC 2 batteries 80A
Argodiode Battery Isolators allow simultaneous charging of two or more batteries from one alternator, without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery. Low voltage drop due to the use of high efficiency Schottky diodes.
Victron BlueSolar MPPT 75/15 Retail
Solar charge controller
75VDC / 15A
12/24 Battery
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron BlueSolar PWM-LCD&USB 48V-30A
Solar charge controller
BlueSolar PWM-LCD&USB
- Liquid Crystal Display
- Two 5 Volt USB outputs
- Lighting control function, fully programmable
- Three stage battery charging (bulk, absorption, float), fully programmable
- Load output with low voltage and manual disconnect (programmable)
- Load output protected against over load and short circuit
- Protected against reverse polarity connection of the solar panels and/or battery
BlueSolar PWM DUO-LCD&USB
All the above-mentioned functions, plus:
- Charges two separate batteries
- Programmable charge current ratio
- External Temperature sensor
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
CSB GP12170 Sealed Lead Acid Battery
5 Year Design Life
12V, 17Ah
NOTE: M5 5mm INSERT BOLT TERMINAL
Please contact us for quantity discounts
Email: info@createenergy.co.za or telephone: +(27) 11 888 0410
Victron BluePower Charger - IP65 - 6V/12V-1.1 + DC connector Smart Charger
Intelligent Charger for WET/Flooded, GEL, AGM, MF, VRLA and Lithium Ion type lead-acid rechargeable batteries.
7 Step "Smart" Battery Charger
180 to 265 V AC Input
12 Volt DC Output
6V/12V-1.1 Amp
IP 65 WaterProof
Free Bluetooth Monitoring & Control App
Victron BatteryProtect 12/24V-100A
The BatteryProtect disconnects the battery from non essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.
The BatteryProtect is a uni-directional device. It can only deal with current in one direction, so either current to a load, or current from a charger, but not both currents at the same time. In addition to this, current only can only flow from the Battery terminal to the Load terminal. In case of use with a load, the battery connects to the Battery terminal, and in case of use with a charger, the charger connects to the Battery terminal.
Freedom Won FW 12-7.5 12V, 7.5Ah Lithium Iron Battery
-
- Nominal Voltage: 12 V.
- Nominal Capacity: 7.5 Ah.
- Energy: 98 Wh.
- Cycle Life: >2000 cycles @ 0.2°C 100% DOD.
- Months Self Discharge: <3%.
- Efficiency of Charge: 100% @ 0.5°C.
- Efficiency of Discharge: 96 – 99% @ 1°C.
- Cell Material: LiFePO4.
- Plastic Case: ABS.
- Dimensions: 151mm x 98mm x 101mm.
- Weight: 1.6Kg.
- Terminal: F2
Victron BlueSolar PWM-Light Charge Controller 48V-20A
Solar charge controller
BlueSolar PWM-Pro
The BlueSolar PWM-Pro series is ready for use with its default settings. It also is fully programmable.
• Lighting control function, fully programmable.
• Three stage battery charging (bulk, absorption, float), fully programmable.
• Integrated battery monitor function (Remote Panel needed to display state of charge).
• Load output with low voltage disconnect and manual control (default setting).
• Optional external temperature sensor.
• Load output protected against over load and short circuit.
• Protected against reverse polarity connection of the solar panels and/or battery.
• Day/night timing options: see manual Remote Panel for details.
BlueSolar PWM-Light
• Load output with low battery voltage disconnect function.
• Lighting control function, one timer only.
• Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting.
• Three stage battery charging (bulk, absorption, float), not programmable.
• Load output protected against over load and short circuit.
• Protected against reverse polarity connection of the solar array and/or battery.
• Day/night timing options: see manual for details
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron Battery Balancer
Victron Orion 12/24-8 DC-DC converter IP20 Non isolated
Remote on/off connector
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by the engine run/stop switch (see manual).
All models with adjustable output can also be used as a battery charger
For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.
All models with adjustable output can be paralleled to increase output current
Up to five units can be connected in parallel.
Victron BlueSolar PWM DUO-LCD&USB 12/24V-20A
Solar charge controller
BlueSolar PWM-LCD&USB
- Liquid Crystal Display
- Two 5 Volt USB outputs
- Lighting control function, fully programmable
- Three stage battery charging (bulk, absorption, float), fully programmable
- Load output with low voltage and manual disconnect (programmable)
- Load output protected against over load and short circuit
- Protected against reverse polarity connection of the solar panels and/or battery
BlueSolar PWM DUO-LCD&USB
All the above-mentioned functions, plus:
- Charges two separate batteries
- Programmable charge current ratio
- External Temperature sensor
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Forbatt 18 AH GEL 12V VRLA Storage Battery
FORBATT GEL 12V Lead Acid Battery
18 AH
APPLICATIONS
Solar Applications
Server Rooms
Telecomms
UPS
3 Year Limited Warranty
Please contact us for quantity discounts
Email: info@createenergy.co.za or telephone: +(27) 11 888 0410
Designed by Fishermen for Fishermen RodBuckle Retractable Rod Hold-Down System by IMMI
RodBuckle Retractable Rod Hold-Down System by IMMI is the most attractive and functional rod hold-down on the market for deck style fishing boats. The self-retracting polyester strap extends a full 24 inches and securely locks into position on the deck.
Rod Buckle
Victron Smart BatteryProtect 12/24 V 65A
Smart BP-65
The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.
When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set.
Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual).
If required, Bluetooth can be disabled.
Victron Interface MK3-US
(VE. BUS to USB-C)
Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Inverter/Charger settings in ECOmulti, EasySolar, EasyPlus, and Inverters with a VE.Bus communication port.
Watersnake Kayak Motor Bracket Mk II
Mount Kit for Electric Trolling Motor
Kayak Motor Mounting Bracket Only (Watersnake)
- Innovative new design (Mark II)
- Bracket that allows you to attach a motor to a kayak quickly and easily
- Suits most kayaks and canoes
- Fits a motor with a maximum shaft diameter of 25mm
- Suit motors up to 24lb thrust providing the shaft diameter is not more than 25mm
Victron BlueSolar MPPT 100/15 Retail
Solar charge controller
100VDC / 15A
12V/24V Battery
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron BlueSolar PWM-Light Charge Controller 48V-30A
Solar charge controller
BlueSolar PWM-Pro
The BlueSolar PWM-Pro series is ready for use with its default settings. It also is fully programmable.
• Lighting control function, fully programmable.
• Three stage battery charging (bulk, absorption, float), fully programmable.
• Integrated battery monitor function (Remote Panel needed to display state of charge).
• Load output with low voltage disconnect and manual control (default setting).
• Optional external temperature sensor.
• Load output protected against over load and short circuit.
• Protected against reverse polarity connection of the solar panels and/or battery.
• Day/night timing options: see manual Remote Panel for details.
BlueSolar PWM-Light
• Load output with low battery voltage disconnect function.
• Lighting control function, one timer only.
• Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting.
• Three stage battery charging (bulk, absorption, float), not programmable.
• Load output protected against over load and short circuit.
• Protected against reverse polarity connection of the solar array and/or battery.
• Day/night timing options: see manual for details
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron Orion 12/24-10 DC-DC converter IP20 Non isolated
Remote on/off connector
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by the engine run/stop switch (see manual).
All models with adjustable output can also be used as a battery charger
For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.
All models with adjustable output can be paralleled to increase output current
Up to five units can be connected in parallel.
Victron SmartSolar MPPT 75/10 Retail
Solar charge controller
75VDC / 10A
12/24 Battery
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron Orion-Tr 48/48-2,5A (120W) Isolated DC-DC converter
Remote on/off
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on/off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
All models are short circuit proof and can be paralleled to increase output current. An unlimited number of units can be connected in parallel.
IP43 protection
When installed with the screw terminals oriented downwards.
Screw terminals
No special tools needed for installation.
Input fuse
On 12V and 24V input models only.
Victron Orion-Tr 48/24-5A (120W) Isolated DC-DC converter
Remote on/off
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on/off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
All models are short circuit proof and can be paralleled to increase output current. An unlimited number of units can be connected in parallel.
IP43 protection
When installed with the screw terminals oriented downwards.
Screw terminals
No special tools needed for installation.
Input fuse
On 12V and 24V input models only.
Victron Orion-Tr 48/12-9A (110W) Isolated DC-DC converter
Remote on/off
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on/off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
All models are short circuit proof and can be paralleled to increase output current. An unlimited number of units can be connected in parallel.
IP43 protection
When installed with the screw terminals oriented downwards.
Screw terminals
No special tools needed for installation.
Input fuse
On 12V and 24V input models only.