Victron BlueSolar PWM-LCD&USB 12/24V-20A
Solar charge controller
BlueSolar PWM-LCD&USB
- Liquid Crystal Display
- Two 5 Volt USB outputs
- Lighting control function, fully programmable
- Three stage battery charging (bulk, absorption, float), fully programmable
- Load output with low voltage and manual disconnect (programmable)
- Load output protected against over load and short circuit
- Protected against reverse polarity connection of the solar panels and/or battery
BlueSolar PWM DUO-LCD&USB
All the above-mentioned functions, plus:
- Charges two separate batteries
- Programmable charge current ratio
- External Temperature sensor
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron Orion IP67 24/12-10A (120W) DC-DC Converter Non Isolated
Completely encapsulated: waterproof, shockproof and ignition protected
Water, oil or dirt will not damage the Orion IP67 DC-DC Converter. The casing is made of cast aluminium and the electronics are moulded in resin.
Victron BATTERY SWITCH ON/OFF 275A
- Max.continuouscurrent: 275A
- One minute rating: 450 A
- Cranking rating: 1200 A
- Voltage rating: 48 V
CSB HRL1234WF2 Sealed Lead Acid Battery
8 Year Design Life
12 Volts
9 Amp Hours
Please contact us for quantity discounts
Email: info@createenergy.co.za or telephone: +(27) 11 888 0410
Forbatt 12 Ah 12V LEAD ACID Storage Battery
FORBAT 12V Lead Acid (AGM- VRLA) Battery
12 AH
APPLICATIONS
Server Rooms
UPS
1 Year Limited Warranty
Please contact us for quantity discounts
Email: info@createenergy.co.za or telephone: +(27) 11 888 0410
Victron BatteryProtect 12/24V-65A
The BatteryProtect disconnects the battery from non essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.
The BatteryProtect is a uni-directional device. It can only deal with current in one direction, so either current to a load, or current from a charger, but not both currents at the same time. In addition to this, current only can only flow from the Battery terminal to the Load terminal. In case of use with a load, the battery connects to the Battery terminal, and in case of use with a charger, the charger connects to the Battery terminal.
A cable to connect Digital Multi Control, Phoenix Inverter Control, Interface MK3-USB, VE.Bus connections between multiple VE.Bus devices and to make VE.Bus and VE.Can connections to a GX device.
Victron Current Transformer 100A:50mA for MultiPlus-II (1m) Wire-end
Victron Orion-Tr 24/12-15 (180W) DC-DC converter Non isolated
Completely encapsulated: waterproof, shockproof and ignition protected
Water, oil or dirt will not damage the Orion IP67 DC-DC Converter. The casing is made of cast aluminium and the electronics are moulded in resin.
Victron Wall mounted enclosure for Color Control GX and BMV or MPPT
GIFT VOUCHER www.createenergy.co.za
Value ZAR 500.00
(Five Hundred South African Rand)
Victron BlueSolar PWM-Light Charge Controller 12/24V-30A
Solar charge controller
BlueSolar PWM-Pro
The BlueSolar PWM-Pro series is ready for use with its default settings. It also is fully programmable.
• Lighting control function, fully programmable.
• Three stage battery charging (bulk, absorption, float), fully programmable.
• Integrated battery monitor function (Remote Panel needed to display state of charge).
• Load output with low voltage disconnect and manual control (default setting).
• Optional external temperature sensor.
• Load output protected against over load and short circuit.
• Protected against reverse polarity connection of the solar panels and/or battery.
• Day/night timing options: see manual Remote Panel for details.
BlueSolar PWM-Light
• Load output with low battery voltage disconnect function.
• Lighting control function, one timer only.
• Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting.
• Three stage battery charging (bulk, absorption, float), not programmable.
• Load output protected against over load and short circuit.
• Protected against reverse polarity connection of the solar array and/or battery.
• Day/night timing options: see manual for details
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron BlueSolar PWM-LCD&USB 48V-10A
Solar charge controller
BlueSolar PWM-LCD&USB
- Liquid Crystal Display
- Two 5 Volt USB outputs
- Lighting control function, fully programmable
- Three stage battery charging (bulk, absorption, float), fully programmable
- Load output with low voltage and manual disconnect (programmable)
- Load output protected against over load and short circuit
- Protected against reverse polarity connection of the solar panels and/or battery
BlueSolar PWM DUO-LCD&USB
All the above-mentioned functions, plus:
- Charges two separate batteries
- Programmable charge current ratio
- External Temperature sensor
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron Busbar to connect 5 Modular Mega Fuse Holders (Victron P/N: CIP100200100)
Victron Smart Battery Sense long range (up to 10m)
Smart Battery Sense is a wireless battery voltage and temperature sensor for Victron MPPT Solar Chargers.
With voltage and temperature sense in place, batteries will be better charged; improving charging-efficiency and prolonging battery life.
Victron Argodiode 80-2SC 2 batteries 80A
Argodiode Battery Isolators allow simultaneous charging of two or more batteries from one alternator, without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery. Low voltage drop due to the use of high efficiency Schottky diodes.
Using the VE.Direct to Bluetooth Smart dongle you can display your BMV or MPPT information on iOS and Android devices, using the VictronConnect App. View information wirelessly such as battery status and solar panel power, plus other useful data.
The dongle is able to read data from all products with a VE.Direct port, such as the BMV-70x series battery monitors, Phoenix Inverters with VE.Direct port, MPPT Solar Charge Controllers.
WATERSNAKE 3-BLADE PROP KIT - REINFORCED NYLON
SUITS ALL 44LB, 54 LB, 65LB & 80LB MOTORS
- Made from reinforced nylon
- Strong and durable
- Designed for Watersnake 65lb - 80lb motors*
- Weedless design
- ALSO FITS MOTORGUIDE 44 lb. Thrust & ABOVE MOTORS
Carry Case for Victron Blue Smart IP65 Chargers and Accessories
Suits Victron Bluesmart IP65 Chargers 24 V / 8 A and 12 V / 25 A
Dimensions 345 x 520 x 130mm
Victron BCD 402 2 batteries 40A (combiner diode)
Diode Battery Combiners are used to guarantee continuous DC power to mission critical equipment, such as an electronic engine control system. With a Diode Battery Combiner two or more DC power sources can be used in parallel to supply the mission critical load. Failure of one source will not interrupt power to the critical load.
Victron Current Transformer 100A:50mA for MultiPlus-II (5m) Wire-end
Victron Remote panel for BlueSolar PWM-Pro Charge Controller
Victron BlueSolar PWM-Light Charge Controller 48V-10A
Solar charge controller
BlueSolar PWM-Pro
The BlueSolar PWM-Pro series is ready for use with its default settings. It also is fully programmable.
• Lighting control function, fully programmable.
• Three stage battery charging (bulk, absorption, float), fully programmable.
• Integrated battery monitor function (Remote Panel needed to display state of charge).
• Load output with low voltage disconnect and manual control (default setting).
• Optional external temperature sensor.
• Load output protected against over load and short circuit.
• Protected against reverse polarity connection of the solar panels and/or battery.
• Day/night timing options: see manual Remote Panel for details.
BlueSolar PWM-Light
• Load output with low battery voltage disconnect function.
• Lighting control function, one timer only.
• Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting.
• Three stage battery charging (bulk, absorption, float), not programmable.
• Load output protected against over load and short circuit.
• Protected against reverse polarity connection of the solar array and/or battery.
• Day/night timing options: see manual for details
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron Orion-Tr 24/12-20 (240W) DC-DC converter Non isolated
Completely encapsulated: waterproof, shockproof and ignition protected
Water, oil or dirt will not damage the Orion IP67 DC-DC Converter. The casing is made of cast aluminium and the electronics are moulded in resin.
Replacement Propeller Kit For Watersnake Advance 24 V 95 lb or 12 V 70 lb Brushless Motor
Includes:
Replacement Propeller
Propeller Spanner
Propeller Nut, Washer and Pin
CSB GP12120 Sealed Lead Acid Battery
5 Year Design Life
12V
12Ah
Please contact us for quantity discounts
Email: info@createenergy.co.za or telephone: +(27) 11 888 0410
The ET112 (for single phase max. 100A) and the ET340 (for three phase max. 65A) Energy Meters are typically used in an Energy Storage System.
To measure the power and energy of the whole application at the distribution box. Or to measure the output of a PV Inverter, to display the data on the Color Control GX and the VRM Portal.
Victron Orion IP67 24/12-20A (240W) DC-DC Converter Non Isolated
Completely encapsulated: waterproof, shockproof and ignition protected
Water, oil or dirt will not damage the Orion IP67 DC-DC Converter. The casing is made of cast aluminium and the electronics are moulded in resin.
Victron Busbar to connect 6 Modular Mega Fuse Holders (Victron P/N: CIP100200100)
Victron BlueSolar PWM-LCD&USB 12/24V-30A
Solar charge controller
BlueSolar PWM-LCD&USB
- Liquid Crystal Display
- Two 5 Volt USB outputs
- Lighting control function, fully programmable
- Three stage battery charging (bulk, absorption, float), fully programmable
- Load output with low voltage and manual disconnect (programmable)
- Load output protected against over load and short circuit
- Protected against reverse polarity connection of the solar panels and/or battery
BlueSolar PWM DUO-LCD&USB
All the above-mentioned functions, plus:
- Charges two separate batteries
- Programmable charge current ratio
- External Temperature sensor
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron BlueSolar MPPT 75/10 Retail
Solar charge controller
75VDC / 10A
12/24 Battery
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Fuse Box - 1 in and 6 out with negative bus bar and LED Indicator
- 6 Circuits with Cover and Negative Bus
- Main Line Terminal Rating: M5 Threaded Studs(100a 32V DC Max)
- Wire Size: #4-6 AWG
- Red LED indicates when fuse is broken
- Size of Panel: 87.75mm x 85.0mm
Victron BlueSolar PWM-LCD&USB 48V-20A
Solar charge controller
BlueSolar PWM-LCD&USB
- Liquid Crystal Display
- Two 5 Volt USB outputs
- Lighting control function, fully programmable
- Three stage battery charging (bulk, absorption, float), fully programmable
- Load output with low voltage and manual disconnect (programmable)
- Load output protected against over load and short circuit
- Protected against reverse polarity connection of the solar panels and/or battery
BlueSolar PWM DUO-LCD&USB
All the above-mentioned functions, plus:
- Charges two separate batteries
- Programmable charge current ratio
- External Temperature sensor
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron Shore Adapter Cord 32A/3 to single ph.-CEE Plug 5P/CEE Coupling 3P
- Input voltage, AC (DC) 220
- Input Current: 32 A
- Connects to Either Shore Power Cable or Shore Power Inlet Socket
- Waterproof: IP 56
- CE Certified: yes
Lowrance RSA Inland Waters Chart
On Micro sd Card with SD Card Adapter
Victron BlueSolar PWM-Pro Charge Controller 12/24V-20A
Solar charge controller
BlueSolar PWM-Pro
The BlueSolar PWM-Pro series is ready for use with its default settings. It also is fully programmable.
• Lighting control function, fully programmable.
• Three stage battery charging (bulk, absorption, float), fully programmable.
• Integrated battery monitor function (Remote Panel needed to display state of charge).
• Load output with low voltage disconnect and manual control (default setting).
• Optional external temperature sensor.
• Load output protected against over load and short circuit.
• Protected against reverse polarity connection of the solar panels and/or battery.
• Day/night timing options: see manual Remote Panel for details.
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron Cyrix-ct 12/24V-120A intelligent battery combiner
Victron smallBMS
A simple and low cost alternative to the VE.Bus BMS V2
The smallBMS can replace the VE.Bus BMS V2 in several applications. It is however not suitable for use with VE.Bus MultiPlus and Quattro inverter/chargers: it has no VE.Bus interface. The smallBMS is intended for use with Victron Smart LiFePo4 batteries with M8 circular connectors.
The smallBMS has two outputs, similar to the VE.Bus BMS V2.
CAB-1 Steel Battery Cabinet on Caster Wheels to hold 1 X 100Ah Battery
Victron BCD 802 2 batteries 80A (combiner diode)
Diode Battery Combiners are used to guarantee continuous DC power to mission critical equipment, such as an electronic engine control system. With a Diode Battery Combiner two or more DC power sources can be used in parallel to supply the mission critical load. Failure of one source will not interrupt power to the critical load.
Victron Argodiode 80-2AC 2 batteries 80A
Argodiode Battery Isolators allow simultaneous charging of two or more batteries from one alternator, without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery. Low voltage drop due to the use of high efficiency Schottky diodes.
Victron BlueSolar MPPT 75/15 Retail
Solar charge controller
75VDC / 15A
12/24 Battery
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron BlueSolar PWM-LCD&USB 48V-30A
Solar charge controller
BlueSolar PWM-LCD&USB
- Liquid Crystal Display
- Two 5 Volt USB outputs
- Lighting control function, fully programmable
- Three stage battery charging (bulk, absorption, float), fully programmable
- Load output with low voltage and manual disconnect (programmable)
- Load output protected against over load and short circuit
- Protected against reverse polarity connection of the solar panels and/or battery
BlueSolar PWM DUO-LCD&USB
All the above-mentioned functions, plus:
- Charges two separate batteries
- Programmable charge current ratio
- External Temperature sensor
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
CSB GP12170 Sealed Lead Acid Battery
5 Year Design Life
12V, 17Ah
NOTE: M5 5mm INSERT BOLT TERMINAL
Please contact us for quantity discounts
Email: info@createenergy.co.za or telephone: +(27) 11 888 0410
Victron BluePower Charger - IP65 - 6V/12V-1.1 + DC connector Smart Charger
Intelligent Charger for WET/Flooded, GEL, AGM, MF, VRLA and Lithium Ion type lead-acid rechargeable batteries.
7 Step "Smart" Battery Charger
180 to 265 V AC Input
12 Volt DC Output
6V/12V-1.1 Amp
IP 65 WaterProof
Free Bluetooth Monitoring & Control App
Victron BatteryProtect 12/24V-100A
The BatteryProtect disconnects the battery from non essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.
The BatteryProtect is a uni-directional device. It can only deal with current in one direction, so either current to a load, or current from a charger, but not both currents at the same time. In addition to this, current only can only flow from the Battery terminal to the Load terminal. In case of use with a load, the battery connects to the Battery terminal, and in case of use with a charger, the charger connects to the Battery terminal.
Freedom Won FW 12-7.5 12V, 7.5Ah Lithium Iron Battery
-
- Nominal Voltage: 12 V.
- Nominal Capacity: 7.5 Ah.
- Energy: 98 Wh.
- Cycle Life: >2000 cycles @ 0.2°C 100% DOD.
- Months Self Discharge: <3%.
- Efficiency of Charge: 100% @ 0.5°C.
- Efficiency of Discharge: 96 – 99% @ 1°C.
- Cell Material: LiFePO4.
- Plastic Case: ABS.
- Dimensions: 151mm x 98mm x 101mm.
- Weight: 1.6Kg.
- Terminal: F2
Victron BlueSolar PWM-Light Charge Controller 48V-20A
Solar charge controller
BlueSolar PWM-Pro
The BlueSolar PWM-Pro series is ready for use with its default settings. It also is fully programmable.
• Lighting control function, fully programmable.
• Three stage battery charging (bulk, absorption, float), fully programmable.
• Integrated battery monitor function (Remote Panel needed to display state of charge).
• Load output with low voltage disconnect and manual control (default setting).
• Optional external temperature sensor.
• Load output protected against over load and short circuit.
• Protected against reverse polarity connection of the solar panels and/or battery.
• Day/night timing options: see manual Remote Panel for details.
BlueSolar PWM-Light
• Load output with low battery voltage disconnect function.
• Lighting control function, one timer only.
• Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting.
• Three stage battery charging (bulk, absorption, float), not programmable.
• Load output protected against over load and short circuit.
• Protected against reverse polarity connection of the solar array and/or battery.
• Day/night timing options: see manual for details
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron Battery Balancer
Victron Orion 12/24-8 DC-DC converter IP20 Non isolated
Remote on/off connector
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by the engine run/stop switch (see manual).
All models with adjustable output can also be used as a battery charger
For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.
All models with adjustable output can be paralleled to increase output current
Up to five units can be connected in parallel.
Victron BlueSolar PWM DUO-LCD&USB 12/24V-20A
Solar charge controller
BlueSolar PWM-LCD&USB
- Liquid Crystal Display
- Two 5 Volt USB outputs
- Lighting control function, fully programmable
- Three stage battery charging (bulk, absorption, float), fully programmable
- Load output with low voltage and manual disconnect (programmable)
- Load output protected against over load and short circuit
- Protected against reverse polarity connection of the solar panels and/or battery
BlueSolar PWM DUO-LCD&USB
All the above-mentioned functions, plus:
- Charges two separate batteries
- Programmable charge current ratio
- External Temperature sensor
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Forbatt 18 AH GEL 12V VRLA Storage Battery
FORBATT GEL 12V Lead Acid Battery
18 AH
APPLICATIONS
Solar Applications
Server Rooms
Telecomms
UPS
3 Year Limited Warranty
Please contact us for quantity discounts
Email: info@createenergy.co.za or telephone: +(27) 11 888 0410
Designed by Fishermen for Fishermen RodBuckle Retractable Rod Hold-Down System by IMMI
RodBuckle Retractable Rod Hold-Down System by IMMI is the most attractive and functional rod hold-down on the market for deck style fishing boats. The self-retracting polyester strap extends a full 24 inches and securely locks into position on the deck.
Rod Buckle
Victron Smart BatteryProtect 12/24 V 65A
Smart BP-65
The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.
When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set.
Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual).
If required, Bluetooth can be disabled.
Victron Interface MK3-US
(VE. BUS to USB-C)
Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Inverter/Charger settings in ECOmulti, EasySolar, EasyPlus, and Inverters with a VE.Bus communication port.
Watersnake Kayak Motor Bracket Mk II
Mount Kit for Electric Trolling Motor
Kayak Motor Mounting Bracket Only (Watersnake)
- Innovative new design (Mark II)
- Bracket that allows you to attach a motor to a kayak quickly and easily
- Suits most kayaks and canoes
- Fits a motor with a maximum shaft diameter of 25mm
- Suit motors up to 24lb thrust providing the shaft diameter is not more than 25mm
Victron BlueSolar MPPT 100/15 Retail
Solar charge controller
100VDC / 15A
12V/24V Battery
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron BlueSolar PWM-Light Charge Controller 48V-30A
Solar charge controller
BlueSolar PWM-Pro
The BlueSolar PWM-Pro series is ready for use with its default settings. It also is fully programmable.
• Lighting control function, fully programmable.
• Three stage battery charging (bulk, absorption, float), fully programmable.
• Integrated battery monitor function (Remote Panel needed to display state of charge).
• Load output with low voltage disconnect and manual control (default setting).
• Optional external temperature sensor.
• Load output protected against over load and short circuit.
• Protected against reverse polarity connection of the solar panels and/or battery.
• Day/night timing options: see manual Remote Panel for details.
BlueSolar PWM-Light
• Load output with low battery voltage disconnect function.
• Lighting control function, one timer only.
• Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting.
• Three stage battery charging (bulk, absorption, float), not programmable.
• Load output protected against over load and short circuit.
• Protected against reverse polarity connection of the solar array and/or battery.
• Day/night timing options: see manual for details
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron Orion 12/24-10 DC-DC converter IP20 Non isolated
Remote on/off connector
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by the engine run/stop switch (see manual).
All models with adjustable output can also be used as a battery charger
For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.
All models with adjustable output can be paralleled to increase output current
Up to five units can be connected in parallel.
Victron SmartSolar MPPT 75/10 Retail
Solar charge controller
75VDC / 10A
12/24 Battery
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron Orion-Tr 48/48-2,5A (120W) Isolated DC-DC converter
Remote on/off
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on/off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
All models are short circuit proof and can be paralleled to increase output current. An unlimited number of units can be connected in parallel.
IP43 protection
When installed with the screw terminals oriented downwards.
Screw terminals
No special tools needed for installation.
Input fuse
On 12V and 24V input models only.
Victron Orion-Tr 48/24-5A (120W) Isolated DC-DC converter
Remote on/off
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on/off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
All models are short circuit proof and can be paralleled to increase output current. An unlimited number of units can be connected in parallel.
IP43 protection
When installed with the screw terminals oriented downwards.
Screw terminals
No special tools needed for installation.
Input fuse
On 12V and 24V input models only.
Victron Orion-Tr 48/12-9A (110W) Isolated DC-DC converter
Remote on/off
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on/off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
All models are short circuit proof and can be paralleled to increase output current. An unlimited number of units can be connected in parallel.
IP43 protection
When installed with the screw terminals oriented downwards.
Screw terminals
No special tools needed for installation.
Input fuse
On 12V and 24V input models only.
Victron Orion-Tr 24/48-2,5A (120W) Isolated DC-DC converter
Remote on/off
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on/off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
All models are short circuit proof and can be paralleled to increase output current. An unlimited number of units can be connected in parallel.
IP43 protection
When installed with the screw terminals oriented downwards.
Screw terminals
No special tools needed for installation.
Input fuse
On 12V and 24V input models only.
Victron Orion-Tr 12/24-5A (120W) Isolated DC-DC converter
Remote on/off
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on/off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
All models are short circuit proof and can be paralleled to increase output current. An unlimited number of units can be connected in parallel.
IP43 protection
When installed with the screw terminals oriented downwards.
Screw terminals
No special tools needed for installation.
Input fuse
On 12V and 24V input models only.
Victron Orion-Tr 12/12-9A (110W) Isolated DC-DC converter
Remote on/off
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on/off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
All models are short circuit proof and can be paralleled to increase output current. An unlimited number of units can be connected in parallel.
IP43 protection
When installed with the screw terminals oriented downwards.
Screw terminals
No special tools needed for installation.
Input fuse
On 12V and 24V input models only.
Victron Orion-Tr 24/24-5A (120W) Isolated DC-DC converter
Remote on/off
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on/off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
All models are short circuit proof and can be paralleled to increase output current. An unlimited number of units can be connected in parallel.
IP43 protection
When installed with the screw terminals oriented downwards.
Screw terminals
No special tools needed for installation.
Input fuse
On 12V and 24V input models only.
Victron Orion-Tr 24/12-9A (110W) Isolated DC-DC converter
Remote on/off
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on/off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
All models are short circuit proof and can be paralleled to increase output current. An unlimited number of units can be connected in parallel.
IP43 protection
When installed with the screw terminals oriented downwards.
Screw terminals
No special tools needed for installation.
Input fuse
On 12V and 24V input models only.
Lowrance 6 foot Ethernet Cable ETHEXT-6YL
Lowrance (Yellow Plug) HighSpeed Ethernet Connection Cable
6 Foot Length
Victron SmartSolar MPPT 75/15 Retail
Solar charge controller
75VDC / 15A
12/24 Battery
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron Argodiode 100-3AC 3 batteries 100A
Argodiode Battery Isolators allow simultaneous charging of two or more batteries from one alternator, without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery. Low voltage drop due to the use of high efficiency Schottky diodes.
Victron Orion 24/12-25A DC-DC converter IP20 Non isolated
Remote on/off connector
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by the engine run/stop switch (see manual).
All models with adjustable output can also be used as a battery charger
For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.
All models with adjustable output can be paralleled to increase output current
Up to five units can be connected in parallel.
CSB EVX12170 Deep Cycle AGM VRLA Traction Sealed Lead Acid Battery (Electric Vehicle)
8 Year Design Life
12 Volts
17 Amp Hours
Please contact us for quantity discounts
Email: info@createenergy.co.za or telephone: +(27) 11 888 0410
Royal Delkor NT 50 26 A/H Storage Battery (DISCONTINUED PRODUCT)
12 Volts
26 A/H
Sealed Maintenance Free
- Calcium maintenance free dual purpose battery
- Wrought lead-calcium grids
- Low-Resistance envelope separators
- High strength polypropylene case
- Heat Sealed covers
- Exclusive patented liquid gas separator
- Built in Hygrometer
Victron Smart BatteryProtect 12/24 V 100 A
Smart BP-100
The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.
When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set.
Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual).
If required, Bluetooth can be disabled.
The Smart Battery Shunt
The SmartShunt is an all in one battery monitor, only without a display. Your phone acts as the display. The SmartShunt connects via Bluetooth to the VictronConnect App on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more.
The Smart Battery Shunt
The SmartShunt is an all in one battery monitor, only without a display. Your phone acts as the display. The SmartShunt connects via Bluetooth to the VictronConnect App on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more.
Victron BlueSolar MPPT 100/20 (up to 48V) Retail Solar Charge Controller 12V/24V/48V
Solar charge controller
100VDC / 20A
12V/24V/48V Battery
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron Current Transformer 100A:50mA for MultiPlus-II (20m)
Victron Current Transformer 100A:50mA for MultiPlus-II (20m) Wire-end
Forbatt 24 AH GEL 12V VRLA Storage Battery
FORBATT GEL 12V Lead Acid Battery
24 AH
APPLICATIONS
Solar Applications
Server Rooms
Telecomms
UPS
3 Year Limited Warranty
Please contact us for quantity discounts
Email: info@createenergy.co.za or telephone: +(27) 11 888 0410
Victron Shore Power Connector Only (No Cable)
Victron Energy CEE Plug 16A (2p/3w)
Victron shore power plug for 250 volt 16 amp European shore power. Made for Victron by Ratio Electric
- Plug and Connector (No Cable)
WATERSNAKE WRIST REMOTE CONTROL REPLACEMENT FOR BOW MOUNT ELECTRIC MOTORS
For use on Tracker, Slither, Fierce and Combat Remote Motors
GIFT VOUCHER www.createenergy.co.za
Value ZAR 1000.00
(One Thousand South African Rand)
Victron BlueSolar PWM-Pro Charge Controller 12/24V-30A
Solar charge controller
BlueSolar PWM-Pro
The BlueSolar PWM-Pro series is ready for use with its default settings. It also is fully programmable.
• Lighting control function, fully programmable.
• Three stage battery charging (bulk, absorption, float), fully programmable.
• Integrated battery monitor function (Remote Panel needed to display state of charge).
• Load output with low voltage disconnect and manual control (default setting).
• Optional external temperature sensor.
• Load output protected against over load and short circuit.
• Protected against reverse polarity connection of the solar panels and/or battery.
• Day/night timing options: see manual Remote Panel for details.
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron Shore Splitter Cord 16A/250V-CEE plug/2xCEE Coupling
- Input voltage, AC (DC) 220
- Input Current: 16 A
- Connects to Either Shore Power Cable or Shore Power Inlet Socket
- Waterproof: IP 56
- CE Certified: yes
Victron Interface MK3-US
(VE. BUS to USB)
Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Inverter/Charger settings in ECOmulti, EasySolar, EasyPlus, and Inverters with a VE.Bus communication port.
Victron Argodiode 120-2AC 2 batteries 120A
Argodiode Battery Isolators allow simultaneous charging of two or more batteries from one alternator, without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery. Low voltage drop due to the use of high efficiency Schottky diodes.
Victron BluePower Charger - IP65 - 12V 4A - Smart Charger
Intelligent Charger for WET/Flooded, GEL, AGM, MF, VRLA and Lithium Ion type lead-acid rechargeable batteries.
7 Step "Smart" Battery Charger
180 to 265 V AC Input
12 Volt DC Output
4 Amp @ 12 V (14,4 - 14,7 V)
IP 65 WaterProof
Free Bluetooth Monitoring & Control App
Pre-Loved - Mecer IVR-1200LBKS Series 1200VA Plug and Play Inverter/Charger
- 1.2kVA / 1200VA / 720 Watt Output
- Includes 3 RSA 3 pin plug points in the top of the inverter
- Plug and Play Inverter/UPS
- Modified Sine Wave Output
- 10 A / 20 A (User Selectable) 12 Volt Battery Charger
1 MONTH WARRANTY
CSB EVH12150 Deep Cycle AGM VRLA Traction Sealed Lead Acid Battery (Electric Vehicle)
5 Year Design Life
12 Volts
15 Amp Hours
Please contact us for quantity discounts
Email: info@createenergy.co.za or telephone: +(27) 11 888 0410
Victron SmartSolar MPPT 100/15 Retail
Solar charge controller
100VDC / 15A
12/24 Battery
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
The ET112 (for single phase max. 100A) and the ET340 (for three phase max. 65A) Energy Meters are typically used in an Energy Storage System.
To measure the power and energy of the whole application at the distribution box. Or to measure the output of a PV Inverter, to display the data on the Color Control GX and the VRM Portal.
Delkor NT50-N24MF (28A19R)
12V
26Ah
Semi-Sealed Maintenance Free
- Calcium maintenance free dual purpose battery
- Low-Resistance envelope separators
- High strength polypropylene case
- Heat Sealed covers
- Exclusive patented liquid gas separator
- Built in Hygrometer
Watersnake Quick Release Trolling Motor Bracket
Nylon
For Electric Steer and Scissor Bracket Type Bow Mount Trolling Motors
Replacement Weedless Propeller Kit for Lowrance Ghost Trolling Motor
Anglers will have no problem fishing in weeds or weedbeds with the optimized design of the Ghost Weedless Prop, which prevent weeds from wrapping around the prop.
It's wise to keep a spare on board at all times, just in case.
Kit includes:
2 Blade Lowrance Weedless Propeller for Ghost Trolling Motor
Propeller Nut
Shaft Pin
Victron BluePower Charger - IP65 - 12V 5A - Smart Charger
Intelligent Charger for WET/Flooded, GEL, AGM, MF, VRLA and Lithium Ion type lead-acid rechargeable batteries.
7 Step "Smart" Battery Charger
180 to 265 V AC Input
12 Volt DC Output
5 Amp @ 12 V (14,4 - 14,7 V)
IP 65 WaterProof
Free Bluetooth Monitoring & Control App
Using the VE.Direct to LoRaWAN module you can connect your BMV, MPPT or Phoenix Inverter to the Victron Remote Management portal. View information such as battery status or solar power wherever you are on your desktop or mobile phone.
Delkor NS40ZLS/42B19L
12V
35Ah
Semi-Sealed Maintenance Free
- Calcium maintenance free dual purpose battery
- Low-Resistance envelope separators
- High strength polypropylene case
- Heat Sealed covers
- Exclusive patented liquid gas separator
- Built in Hygrometer
Victron SmartSolar MPPT 100/20 (up to 48V) Retail
Solar charge controller
100VDC / 20A
12/24/48V Battery
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
Victron Argodiode 160-2AC 2 batteries 160A
Argodiode Battery Isolators allow simultaneous charging of two or more batteries from one alternator, without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery. Low voltage drop due to the use of high efficiency Schottky diodes.
Royal Delkor NS 40 35 A/H Storage Battery
12 Volts
35 A/H
Sealed Maintenance Free
- Calcium maintenance free dual purpose battery
- Wrought lead-calcium grids
- Low-Resistance envelope separators
- High strength polypropylene case
- Heat Sealed covers
- Exclusive patented liquid gas separator
- Built in Hygrometer
CSB GP12260 Sealed Lead Acid Battery
5 Year Design Life
12V
26Ah
VRLA AGM
Please contact us for quantity discounts
Email: info@createenergy.co.za or telephone: +(27) 11 888 0410
Victron Orion 24/12-40A DC-DC converter Non isolated
Remote on/off connector
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by the engine run/stop switch (see manual).
All models with adjustable output can also be used as a battery charger
For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.
All models with adjustable output can be paralleled to increase output current
Up to five units can be connected in parallel.
The VE.Bus Smart dongle is two products in one:
Bluetooth accessory for range of inverter/chargers and our series of Phoenix Inverters with a VE.Bus port.
Secondly it can work as a Voltage- and Temperature-sense device for the inverter/charger. This works with all models.
Victron BluePower Charger - IP67 - 12V 7A - Smart Charger
Intelligent Charger for WET/Flooded, GEL, AGM, MF, VRLA and Lithium Ion type lead-acid rechargeable batteries.
5 Step "Smart" Battery Charger
180 to 265 V AC Input
24 Volt DC Output
7 Amp @ 12 V (14.4 - 14.7 V)
IP 67 WaterProof
Free Bluetooth Monitoring & Control App
Freedom Won FW 12-20 12 V, 20 Ah Lithium Iron Battery
-
- Nominal Voltage: 12V.
- Nominal Capacity: 20Ah.
- Energy: 256Wh.
- Cycle Life: >2000 cycles @ 0.2°C 100% DOD.
- Months Self Discharge: <3%.
- Efficiency of Charge: 100% @ 0.5°C.
- Efficiency of Discharge: 96 – 99% @ 1°C.
- Cell Material: LiFePO4.
- Plastic Case: ABS.
- Dimensions: 181mm x 77mm x 167mm.
- Weight: 2.75Kg.
- Terminal: M5
CSB EVX12200 Deep Cycle AGM VRLA Traction Sealed Lead Acid Battery (Electric Vehicle)
8 Year Design Life
12 Volts
20 Amp Hours
Please contact us for quantity discounts
Email: info@createenergy.co.za or telephone: +(27) 11 888 0410
Victron Shore Power Inlet stainless with cover 16A/250Vac (2p/3w)
- Current Rating (A): 16
- Voltage Rating: 250
- Standard: IEC 60309, 2p+E
Cover:
- Solid cast
- 316 Stainless Steel
- Plug body : PA6
- Pins: Brass, Nickel plated
- Weight (kg): 0,65
- Waterproof: IP 56
- CE Certified: yes
Victron Argodiode 140-3AC 3 batteries 140A
Argodiode Battery Isolators allow simultaneous charging of two or more batteries from one alternator, without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery. Low voltage drop due to the use of high efficiency Schottky diodes.
Pre-Loved Mecer IVR-2400LBKS Series 2400VA Plug and Play Inverter/Charger
- 2.4kVA / 2400VA / 1440 Watt
- Includes 3 RSA 3 pin plug points in the top of the inverter
- Plug and Play Inverter/UPS
- Modified Sine Wave Output
PRE LOVED - 1 MONTH WARRANTY
Victron Phoenix Inverter 48/250 230V VE.Direct SHUKO
Inverter
Victron Phoenix Inverter 24/250 230V VE.Direct SCHUKO
Inverter
Victron Phoenix Inverter 12/250 230V VE.Direct SCHUKO
Inverter
Victron BatteryProtect 12/24V-220A
The BatteryProtect disconnects the battery from non essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.
The BatteryProtect is a uni-directional device. It can only deal with current in one direction, so either current to a load, or current from a charger, but not both currents at the same time. In addition to this, current only can only flow from the Battery terminal to the Load terminal. In case of use with a load, the battery connects to the Battery terminal, and in case of use with a charger, the charger connects to the Battery terminal.
This pair of Zigbee converters is to wirelessly connect an Energy Meter to a GX Device.
You will require both products to connect the Energy Meter to a GX Device
Zigbee to USB converter, DRF2658C, DTK (THIS PRODUCT P/N: ASS300420200)
Zigbee to RS485 converter, DRF2659C, DTK (NEEDED AS WELL, NOT INCLUDED P/N: ASS300420100, Link to product: https://createenergy.co.za/home/566-victron-zigbee-to-rs485-converter-wireless-for-et112-et340-em24-energy-meters-8719076048268.html
Create Energy CAB-2 Steel Battery Trolley for 2 x 100 Ah Batteries
Satin Black
On Castors
With Single Pole Isolator Switch
Delivered in Flat Pack Packaging
Easy to Assemble
Clip Together Construction
Satin Black Finish
Holds 2 x Group 31, 3 x Group 27 or 2 x Power Protectors 12 V 100 Ah AGM VRLA Batteries (H) 275 x W 173 x 407 (L)
Plug and Play Victron Inverter / Charger Add On
The VE.Bus Smart dongle is two products in one:
Bluetooth accessory for range of inverter/chargers and our series of Phoenix Inverters with a VE.Bus port.
Secondly it can work as a Voltage- and Temperature-sense device for the inverter/charger. This works with all models.
Includes 0.9m RJ45 Cable between VE.Bus Smart dongle and Inverter / Charger
The ET112 (for single phase max. 100A) and the ET340 (for three phase max. 65A) Energy Meters are typically used in an Energy Storage System.
To measure the power and energy of the whole application at the distribution box. Or to measure the output of a PV Inverter, to display the data on the Color Control GX and the VRM Portal.
The Smart Battery Shunt
The SmartShunt is an all in one battery monitor, only without a display. Your phone acts as the display. The SmartShunt connects via Bluetooth to the VictronConnect App on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more.
Victron Argofet 100-2 Two batteries 100A
Similarly to Argodiode battery isolators, Argofet isolators allow simultaneous charging of two or more batteries from one alternator (or a single output battery charger), without connecting the batteries together. In contrast with Argodiode battery isolators, Argofet isolators have virtually no voltage loss. Voltage drop is less than 0,02 Volt at low current and averages 0,1 Volt at higher currents.
Victron Shore Power Connector Only (No Cable)
Victron Energy CEE Plug 32A (2p/3w)
Victron shore power plug for 250 volt 32 amp European shore power. Made for Victron by Ratio Electric
- Plug and Connector (No Cable)
Delkor NS60S/50B24RS
12V
45Ah
Semi-Sealed Maintenance Free
- Calcium maintenance free dual purpose battery
- Low-Resistance envelope separators
- High strength polypropylene case
- Heat Sealed covers
- Exclusive patented liquid gas separator
- Built in Hygrometer
Atlas Series Hot Shot™
Jack Plate Hole Shot Plate
For 6 inch MODEL
AHJHSP-6V-DP
PLEASE CONTACT US TO CONFIRM PRICE AND AVAILABILITY
Victron BluePower Charger - IP67 - 24V 5A - Smart Charger
Intelligent Charger for WET/Flooded, GEL, AGM, MF, VRLA and Lithium Ion type lead-acid rechargeable batteries.
5 Step "Smart" Battery Charger
180 to 265 V AC Input
24 Volt DC Output
5 Amp @ 12 V (28,8 - 29,4 V)
IP 67 WaterProof
Free Bluetooth Monitoring & Control App
Garmin Trolling Motor DC Circuit Breaker / Isolator 60A - 42 Volt
Circuit Breaker / Isolator / Cut Out
Warning: Use a minnimum of 10mm square cable
Royal Delkor NS 60 45 A/H Storage Battery
12 Volts
45 A/H
Sealed Maintenance Free
- Calcium maintenance free dual purpose battery
- Wrought lead-calcium grids
- Low-Resistance envelope separators
- High strength polypropylene case
- Heat Sealed covers
- Exclusive patented liquid gas separator
- Built in Hygrometer
Sun Inverter 24/250-15 IEC
The Sun Inverter combines a sinewave inverter and a PWM solar charger in one enclosure and is easy to install, with a minimum of wiring.
The inverter allows you to power domestic equipment - requiring 230V AC - using 'leisure' or 'automotive' batteries rated at 12V or 24V.The solar charger ensures that the batteries are being charged by energy harvested from your solar panels. The charge algorithm is programmable.
The inverter and solar charger parameters can be read out via Bluetooth using the VictronConnect app. In addition to this, the inverter has a VE.Direct Port for connection to a GX device or GlobalLink 520 for system monitoring.
Sun Inverter 12/250-15 IEC
The Sun Inverter combines a sinewave inverter and a PWM solar charger in one enclosure and is easy to install, with a minimum of wiring.
The inverter allows you to power domestic equipment - requiring 230V AC - using 'leisure' or 'automotive' batteries rated at 12V or 24V.The solar charger ensures that the batteries are being charged by energy harvested from your solar panels. The charge algorithm is programmable.
The inverter and solar charger parameters can be read out via Bluetooth using the VictronConnect app. In addition to this, the inverter has a VE.Direct Port for connection to a GX device or GlobalLink 520 for system monitoring.
Forbatt 33Ah GEL 12V VRLA Storage Battery
FORBATT GEL 12V Lead Acid Battery
33Ah
APPLICATIONS
Solar Applications
Server Rooms
Telecomms
UPS
3 Year Limited Warranty
Please contact us for quantity discounts
Email: info@createenergy.co.za or telephone: +(27) 11 888 0410
Create Energy CAB-2 COMPACT Steel Battery Trolley for 2 x 100 Ah Batteries
HAMMERTONE BLACK
On Heavy Duty Castors
Delivered PRE ASSEMBLED
Hammertone Black Finish
Holds 2 x Group or 2 x Group 27 Batteries
Victron Argodiode 180-3AC 3 batteries 180A
Argodiode Battery Isolators allow simultaneous charging of two or more batteries from one alternator, without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery. Low voltage drop due to the use of high efficiency Schottky diodes.
Forbatt 40 AH AGM 12V VRLA Storage Battery
FORBATT AGM12V Lead Acid Battery
40 AH
APPLICATIONS
Solar Applications
Server Rooms
Telecomms
UPS
1 Year Limited Warranty
Please contact us for quantity discounts
Email: info@createenergy.co.za or telephone: +(27) 11 888 0410
Victron Battery Monitor BMV-700 Retail
The BMV-700 is a high precision battery monitor. The essential function of a battery monitor is to calculate ampere hours consumed and the state of charge of a battery. Ampere hours consumed are calculated by integrating the current flowing in or out of the battery.
6.5 - 95V
The Smart Battery Shunt
The SmartShunt is an all in one battery monitor, only without a display. Your phone acts as the display. The SmartShunt connects via Bluetooth to the VictronConnect App on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more.
Victron Smart BatteryProtect 12/24 V 220 A
Smart BP-220
The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.
When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set.
Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual).
If required, Bluetooth can be disabled.
Victron BluePower Charger - IP65 - 24 V 5 A - Smart Charger
Blue Smart IP65 Charger 24/5(1) 230V CEE 7/16 Retail
Intelligent Charger for WET/Flooded, GEL, AGM, MF, VRLA and Lithium Ion type lead-acid rechargeable batteries.
7 Step "Smart" Battery Charger
180 to 265 V AC Input
24 Volt DC Output
5 Amp @ 24 V (28,8 - 29,4 V)
IP 65 WaterProof
Free Bluetooth Monitoring & Control App
Victron BluePower Charger - IP65 - 12V 7 A - Smart Charger
Intelligent Charger for WET/Flooded, GEL, AGM, MF, VRLA and Lithium Ion type lead-acid rechargeable batteries.
7 Step "Smart" Battery Charger
180 to 265 V AC Input
12 Volt DC Output
7 Amp @ 12 V (14,4 - 14,7 V)
IP 65 WaterProof
Free Bluetooth Monitoring & Control App
Victron BlueSolar MPPT 100/30 Solar Charge Controller 12V/24V
Solar charge controller
100VDC / 20A
12V/24V Battery
CONTACT US FOR QUANTITY DISCOUNTS / INSTALLER / RESELLER PRICING
info@createenergy.co.za / 0118880410
CSB GPL12260 Sealed Lead Acid Battery
10 Year Design Life
12V
26 Amp Hours
Please contact us for quantity discounts
Email: info@createenergy.co.za or telephone: +(27) 11 888 0410
CSB HRL12110W Sealed Lead Acid Battery
8-10 Year Design Life
12 Volts
28 Amp Hours
148W
Please contact us for quantity discounts
Email: info@createenergy.co.za or telephone: +(27) 11 888 0410
This pair of Zigbee converters is to wirelessly connect an Energy Meter to a GX Device.
You will require both products to connect the Energy Meter to a GX Device
Zigbee to USB converter, DRF2658C, DTK (NEEDED AS WELL, NOT INCLUDED P/N: ASS300420200) Link to the product: https://createenergy.co.za/home/567-victron-zigbee-to-usb-converter-converter-wireless-for-et112-et340-em24-energy-meters-to-gx-device-8719076048275.html
Zigbee to RS485 converter, DRF2659C, DTK (THIS PRODUCT, P/N: ASS300420100)
Victron Orion-Tr 48/24-12A (280W) Isolated DC-DC converter
Remote on/off
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on/off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
All models are short circuit proof and can be paralleled to increase output current. An unlimited number of units can be connected in parallel.
IP43 protection
When installed with the screw terminals oriented downwards.
Screw terminals
No special tools needed for installation.
Input fuse
On 12V and 24V input models only.
Victron Orion-Tr 24/48-6A (280W) Isolated DC-DC converter
Remote on/off
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on/off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
All models are short circuit proof and can be paralleled to increase output current. An unlimited number of units can be connected in parallel.
IP43 protection
When installed with the screw terminals oriented downwards.
Screw terminals
No special tools needed for installation.
Input fuse
On 12V and 24V input models only.
Victron Orion-Tr 24/12-20A (240W) Isolated DC-DC converter
Remote on/off
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on/off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
All models are short circuit proof and can be paralleled to increase output current. An unlimited number of units can be connected in parallel.
IP43 protection
When installed with the screw terminals oriented downwards.
Screw terminals
No special tools needed for installation.
Input fuse
On 12V and 24V input models only.
Victron Orion-Tr 48/48-6A (280W) Isolated DC-DC converter
Remote on/off
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on/off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
All models are short circuit proof and can be paralleled to increase output current. An unlimited number of units can be connected in parallel.
IP43 protection
When installed with the screw terminals oriented downwards.
Screw terminals
No special tools needed for installation.
Input fuse
On 12V and 24V input models only.