Jarvis Walker Watersnake ASP 24 SW 24 Pound Thrust Transom Mount Trolling Motor
Kayak and Kickboat Trolling Motor
12 Volt
24 lb Thrust
24" Shaft
Hi / Lo Speed & Forward / Reverse
Fixed Tiller Handle
White
Fresh & Salt Water
Jarvis Walker ASP 18-SW 18 Pound Transom Mount Electric Motor
12 Volt
18 lb Thrust
24" Shaft
Hi / Lo Speed & Forward / Reverse
Fixed Tiller Handle
White
Fresh & Salt Water
Lowrance ActiveTarget 2 (Module + Transducer + Mounts)
ActiveTarget® 2 gives you the highest resolution, widest, and clearest live views of fish and structure. By watching fish respond to your lure in real-time, you can make the quick adjustments that make the difference and help you catch more fish.
COMPATABLE WITH
HDS PRO
HDS LIVE
HDS CARBON
ELITE FS
Lowrance ActiveImaging HD 3-in-1 Nose Cone Transducer for Ghost Trolling Motor
Step up to the ultimate fishfinding clarity with new, high-definition Active Imaging™ HD 3-in-1 sonar. Get the clearest images of fish and structure from Lowrance® CHIRP sonar, high-frequency (up to 1.2MHz) SideScan/DownScan Imaging™, plus FishReveal™ DownScan and a new FishReveal SideScan* view,.
Active Imaging 3-in-1 Nosecone Transducer for Ghost Trolling Motor
Lowrance HDI Nosecone Transducer for Ghost Trolling Motor
Power 600 Watt
Shallow Water (</= 300 m / 1000 ft)
Cone Angle:
200 khz: 20 Degree
83 khz: 60 Degree
With Temperature
With "Down - Imaging" 455-800 Khz
Lowrance TMR-1 Ghost Trolling Motor Remote Control
Key Features
Adjust speed
Change direction
Set Anchor
Includes lanyard
Hand Held
Wireless
Lowrance Ghost 24 V / 36 V Trolling Motor
24 / 36 V
47 / 52 / 60 inch Shaft Options
ADD THE LOWRANCE ACTIVE IMAGING 3-IN-1 NOSECONE TO ACTIVATE THE GHOST 360 SCANNING FEATURE!
Victron smallBMS
A simple and low cost alternative to the VE.Bus BMS V2
The smallBMS can replace the VE.Bus BMS V2 in several applications. It is however not suitable for use with VE.Bus MultiPlus and Quattro inverter/chargers: it has no VE.Bus interface. The smallBMS is intended for use with Victron Smart LiFePo4 batteries with M8 circular connectors.
The smallBMS has two outputs, similar to the VE.Bus BMS V2.
Victron VE.Bus BMS V2
The VE.Bus BMS V2 is a Battery Management System (BMS) designed to interface with and protect a single, or multiple Victron Lithium Battery Smart 12,8V & 25,6V (LiFePO4 or LFP) in systems that have Victron inverters or inverter/chargers with VE.Bus communication. It monitors and protects the batteries against over voltage and under voltage of any individual cell, and also over temperature or under temperature conditions.
Based on the status of the battery or batteries, the BMS will:
- Generate a pre-alarm signal to alert of an imminent cell under voltage condition.
- Disable inverting in VE.Bus inverters or inverter/chargers via VE.Bus, and disable other loads via the 'Load Disconnect' terminal in the event of a cell under voltage condition.
- Disable charging in VE.Bus inverters or inverter/chargers via VE.Bus and disable other chargers via the 'Charge Disconnect' terminal in the event of a cell overvoltage, under temperature or over temperature condition.
- Remote on/off terminals.
- Ability to disable VE.Direct and VE.Can solar chargers via a GX device.
- Allowing control of the VE.Bus inverter/charger from multiple devices, like the Digital Multi Control, the VE.Bus Smart dongle and/or a GX device.
- Auxiliary power input and output terminals that allow a GX device to remain powered in the event of a system shutdown.
Victron VE.Bus BMS
The VE.Bus BMS is a Battery Management System (BMS) designed to interface with and protect a single, or multiple Victron Lithium Battery Smart 12,8V & 25,6V (LiFePO4 or LFP) in systems that have Victron inverters or inverter/chargers with VE.Bus communication. It monitors and protects the batteries against over voltage and under voltage of any individual cell, and also over temperature or under temperature conditions.
Based on the status of the battery or batteries, the BMS will:
- Generate a pre-alarm signal to alert of an imminent cell under voltage condition.
- Disable inverting in VE.Bus inverters or inverter/chargers via VE.Bus, and disable other loads via the 'Load Disconnect' terminal in the event of a cell under voltage condition.
- Disable charging in VE.Bus inverters or inverter/chargers via VE.Bus and disable other chargers via the 'Charge Disconnect' terminal in the event of a cell overvoltage, under temperature or over temperature condition.
- Remote on/off terminals.
- Ability to disable VE.Direct and VE.Can solar chargers via a GX device.
- Allowing control of the VE.Bus inverter/charger from multiple devices, like the Digital Multi Control, the VE.Bus Smart dongle and/or a GX device.
- Auxiliary power input and output terminals that allow a GX device to remain powered in the event of a system shutdown.
Victron Phoenix Smart IP43 Charger 24/16(3) 230V
Wide AC Input Range 120-240 Vac
Adjustable DC Output Current Setting
Ready for Parallel and Redundant Operation
Natural Convection Cooling
Adaptive 5 Stage Charge Algorithm
Less than 1 mA Self Consumption
Full Rated Output up to 40 Deg C
IP43 Degree of Ingress Protection
Requires CE 13 "Kettle" Plug - Not Included
Victron Phoenix Phoenix Smart IP43 Charger 24/16(1+1) 230V
</ = 16 A Main House Battery Charger Plus </= 4 A Battery Maintainer for 24 V Primary Cranking Battery
Wide AC Input Range 120-240 Vac
Adjustable DC Output Current Setting
Ready for Parallel and Redundant Operation
Natural Convection Cooling
Adaptive 5 Stage Charge Algorithm
Less than 1 mA Self Consumption
Full Rated Output up to 40 Deg C
IP43 Degree of Ingress Protection
Requires CE 13 "Kettle" Plug - Not Included
Victron Phoenix Smart IP43 Charger 12/50(3) 230V
Wide AC Input Range 120-240 Vac
Adjustable DC Output Current Setting
Ready for Parallel and Redundant Operation
Natural Convection Cooling
Adaptive 5 Stage Charge Algorithm
Less than 1 mA Self Consumption
Full Rated Output up to 40 Deg C
IP43 Degree of Ingress Protection
Requires CE 13 "Kettle" Plug - Not Included
Victron Phoenix IP43 Smart Charger 12 V / 50 A (1+1) 230V
</ = 50 A Main House Battery Charger Plus </= 4 A Battery Maintainer for Primary Cranking Battery
Wide AC Input Range 120-240 Vac
Adjustable DC Output Current Setting
Ready for Parallel and Redundant Operation
Natural Convection Cooling
Adaptive 5 Stage Charge Algorithm
Less than 1 mA Self Consumption
Full Rated Output up to 40 Deg C
IP43 Degree of Ingress Protection
Requires CE 13 "Kettle" Plug - Not Included
Victron Phoenix IP43 Smart Charger 12 V / 30 A (1+1) 230V
</ = 30 A Main House Battery Charger Plus </= 4 A Battery Maintainer for Primary Cranking Battery
Wide AC Input Range 120-240 Vac
Adjustable DC Output Current Setting
Ready for Parallel and Redundant Operation
Natural Convection Cooling
Adaptive 5 Stage Charge Algorithm
Less than 1 mA Self Consumption
Full Rated Output up to 40 Deg C
IP43 Degree of Ingress Protection
Requires CE 13 "Kettle" Plug - Not Included
Victron Phoenix Smart IP43 Charger 24/25(3) 120-240V
Wide AC Input Range 120-240 Vac
Adjustable DC Output Current Setting
Ready for Parallel and Redundant Operation
Natural Convection Cooling
Adaptive 5 Stage Charge Algorithm
Less than 1 mA Self Consumption
Full Rated Output up to 40 Deg C
IP43 Degree of Ingress Protection
Requires CE 13 "Kettle" Plug - Not Included
Victron Phoenix Smart IP43 Charger 12/50(3) 120-240V
Wide AC Input Range 120-240 Vac
Adjustable DC Output Current Setting
Ready for Parallel and Redundant Operation
Natural Convection Cooling
Adaptive 5 Stage Charge Algorithm
Less than 1 mA Self Consumption
Full Rated Output up to 40 Deg C
IP43 Degree of Ingress Protection
Requires CE 13 "Kettle" Plug - Not Included